spsemi rev 2016 12 12 ... www.spsemi.cn page 1 of 4 surge & esd protection device spe06r series features low voltage overshoot low on-state voltage does not degrade surge capability after multiple surge events within limit fails short circuit when surged in excess of ratings bi-directional protection device rohs compliance s.e.t/spe06r series applicable global standards tia-968-a tia-968-b itu k.20/21 enhanced level * gr 1089 intra-building yd/t 1082 yd/t 993 yd/t 950 itu k.20/21 basic level gr 1089 inter-building * iec compatibility iec 61000-4-2 (esd) 5kv (air) kv (contact) 1,8 iec 61000-4-5 (surge) 10/700 s 2kv(spe06ra,spe06ral) s 4kv(spe06rb,SPE06RBL) iec 6100 045surge 10 700 / - - ( ) * a/b-rated parts require series resistance product name spe06ra l default l: low capacitance surge ratings: a: iec6100-4-5(surge) 10/700us 2kv b: iec6100-4-5(surge) 10/700us 4kv c: iec6100-4-5(surge) 10/700us 6kv packge type: r:do-214ac s:do-214aa t:sod-123 v rwm type designation applications audio/video line network and telecom data lines and security systems serial ports
spsemi rev 2016 12 12 ... www.spsemi.cn page 2 of 4 maximum ratings (t =25 unless otherwise specified ) a rating symbol value units termal resistance:junction to ambient operating junction storage temperature range rj ba t j t s 90 40 to +150 - - 65 to +150 / w dimensions (do-214ac) electrical characteristics (t =25 unless otherwise specified ) a 0.065 1.65 () 0.049 1.25 () 0.185(4.70) 0.157(3.99) 0.112(2.85) 0.094(2.40) 0.090(2.29) 0.078(1.98) 0.208 5.28 () 0.185 4.70 () 0.012 0.305 () 0.006 0.152 () 0.060 1.52 () 0.030 0.76 () do-214ac(sma j-bend) dimensions in inches and(millimeters) 0.008(0.203)max. s.e.t/spe06r series spe06r part number v br i r @v rwm i h device marking code spe06ra spe06rb spe06ral SPE06RBL e06a e06b eba eca 6.5 6.5 6.5 6.5 8.0 8.0 8.0 8.0 15.0 15.0 15.0 15.0 3 3 2 2 20 20 20 20 40 60 15 40 typical application circuit video chip set .. 10-20ohm 75ohm 75ohm resistance is the original video matching resistance rs485 s rs485 r s 5 5 5 5 4 4 4 4
spsemi rev 2016 12 12 ... www.spsemi.cn page 3 of 4 typical characteristics curves fig.1 tr td pulse wave-form 0 half value peak value waveform=t t r d tr=rise time to peak value td=decay time to half value 50 100 150 i -peak pulse current-%i pp pp t-time(s) t d t r fig.2 esd discharge iec61000-4-2 current waveform 100% t 90% tp=0.7-1ns i peak fig.3 power derating curve fig.4 junction capacitance vs. reverse voltage 0255075 100 125 150 175 0 20 60 80 100 t -ambient temperature( ) a % of rated power or i pp c (v =0v)/c (v )(pf) j rjr 0 1 voltage-v (v) r 40 120 2 3 4 5 1 1.1 1.2 1.3 1.4 1.5 1.6 s.e.t/spe06r series fig.5 normalized vs change versus junction temperature percent of v change-% s -40 0 junction temerature(t )- j 20 40 120 140 -8 -6 0 4 8 10 14 -4 2 6 12 -20 60 80 100 160 fig.6 normalized dc holding current 0.4 0.6 1.2 1.4 1.8 1.0 -40 0 case temerature(t )- c 20 40 120 140 -20 60 80 100 160 0.8 1.6 ratio of i h i(t=25 ) hc 2.0
spsemi rev 2016 12 12 ... www.spsemi.cn page 4 of 4 marking code e06a **** marking code logo date code recommended soldering conditions recommended conditions reflow soldering t s t p t l time 25 time to peak temperature (t 25 to peak) temperature t (min) s t (max) s t l t p preheat ramp-down ramp-up critical zone ttot lp re?ow condition pb-free assembly pre heat -temperature min(t ) s(min) -temperature max(t ) s(max) -time(min to max)(t ) s average ramp up rate (liquidus temp(t ) to peak) l t to t -ramp-up rate s(max) l re?ow -temperature(t )(liquidus) l -temperature(t ) l peak temp(t ) p time within 5 of actual peak temp(t ) p ramp-down rate time 25 to peak temp(t ) p do not exceed +150 +200 60-180secs 3 /sec.max. 3 /sec.max. +217 60-150secs +260(+0/-5) 30 secs.max. 6 /sec.max. 8 min.max. +260 s.e.t/spe06r series tape and reel specification symbol ea per reel reel dia(mm) industry standard spe06r** 5000 330 eia rs-481 0.157 (4.0) 0.47 (12.0) 0.157 (4.0) 0.47 (12.0) 13.0(330)
|
